Adhesives Tapes Glue & Epoxy

Flex-Fletch Zing! Kling Adhesive Tube

About the product

Zing! Kling Adhesive Tube for Fletching
Zing! Kling Adhesive provides the fletcher with confidence that the process of fletching will be trouble-free and that the vanes will stay on. Zing! Kling is think enough to resist running and rubber-toughened to withstand high-speed abuse. It is the toughest fletching adhesive on the market!

How To Use the Zing! Kling Adhesive Tube
Surfaces to be bonded should be clean and dry. Apply only enough to leave a thin film layer after compression. Press parts together and hold firmly for a few seconds. Good contact is essential and an adequate bond develops in less than one minute. For a quicker cure time and stronger bond, use a Zing! Fletching primer Pen or Pint beforehand.

Optimal Set-Time 30-60 seconds
Full cure 24 hours
Full cure with Zing! Primer 8 hours
Product Size 0.7oz - 20g tube
Extra Spout / Cap Encase mistakes happen, an extra spout - cap is included

Archery Tech Team

Flex-Fletch Zing! Fletching Primer Pen

About the product

Zing! Fletching Primer Pen Makes Fletching Arrows a Breeze!
The Zing! Fletching Primer Pen is the easiest, fastest, and strongest way to fletch your arrows.
Zing! fletching primer was the first primer to break onto the archery scene in the United States and is still the leader. It is an ozone friendly primer used to prepare polyolefin surfaces for bonding with cyanoacrylate adhesives (CA). It speeds up the adhesion process and strengthens it when bonding with Zing! adhesion glues.

How To Use the Zing! Fletching Primer Pen
The Zing! Fletching Primer Pen uses a plunge-action to wet the fiber tip with the correct amount of primer for precision application of the primer to the base of the vane or other plastic/rubber parts. There's no waste and no mess, even if you forget to put the cap back on! It is ideally used with a Zing! Kling adhesive tube. It also works well with most other cyanoacrylate adhesives. Not intended for use with solvent type adhesives such as Flex-Bond, Saunder NPV, or Bohning Platinum.

Dry Time 15-30 seconds
On-Part Life 5 minutes
Ideal Adhesive Zing! Kling Adhesive Tube
Full cure with Zing! Kling Adhesive Tube: 8 hours (24 hours without Zing! Fletching Primer)
Product Size 11 gm pre-loaded plunge-tip pen

Archery Tech Team

Q2i Archery Steel Bond Fletch Glue Remover 1.0 Oz

About the product

Decrease arrow prep time.
Solvent eats away glue while not harming arrow shaft.
Safe to use with aluminum, carbon & fiberglass.

1 oz. bottle

Test for color fastness on an inconspicuous are before using.

Archery Tech Team

Q2i Archery Steel Bond Fletch Glue 1.0 Oz

About the product

Incredible Control, Unreal Hold!

Super high viscosity for easy control
Clamp time 15 seconds, full cure 4-8 hours*
For fletching aluminum, carbon, fiberglass & wood

Times stated are for when used in conjunction with Q2i Archery Dual Polymer Technology Vanes. Other vanes and vane manufacturers products may differ.

Archery Tech Team

Q2i Archery Steel Bond Fletch Glue 0.5 Oz

About the product

Incredible Control, Unreal Hold!

Super high viscosity for easy control
Clamp time 15 seconds, full cure 4-8 hours*
For fletching aluminum, carbon, fiberglass & wood

Times stated are for when used in conjunction with Q2i Archery Dual Polymer Technology Vanes. Other vanes and vane manufacturers products may differ.

Archery Tech Team

Bohning Hot Melt Cool Flex

About the product

Ferr-L-Tite Cool Flex® is designed for points, inserts, outserts, and pin bushings on carbon shafts. This hot melt adhesive has flexible properties which keep it from cracking even after repeated target impacts. Cool Flex is a must for carbon shafts, but it also works great on aluminum and fiberglass. It requires a flame for installation, but just use HOT WATER for easy adjustment, replacement, or removal of points, inserts, outserts, and pin bushings. Cool Flex is fully cured as soon as it reaches room temperature (about 5 minutes), and its melting point is 280°F (137.8°C). Available in 12 gram sticks and 1 pound bricks. No expiration. Certified Crossbow Compatible.Proudly manufactured at the Bohning factory in Lake City, Michigan, United States.

Archery Tech Team

Bohning Hot Melt Ferr-L-Tite

About the product

Ferr-L-Tite® was Bohning's first product, developed in 1946, and has been the archery industry's standard ever since! This hot melt adhesive is designed for points, inserts, and outserts on wood and aluminum shafts (for carbon, we recommend Ferr-L-Tite Cool Flex). It requires an open flame for installation or removal and is fully cured as soon as it reaches room temperature (about 5 minutes). Ferr-L-Tite is heat reversible on aluminum shafts - flame required. It has a melting point of 350° F (176.7°C). Available in 12 gram sticks and 1 pound bricks. No expiration date. Certified Crossbow Compatible. Proudly manufactured at the Bohning factory in Lake City, Michigan, United States.

Archery Tech Team

XS Wings Fletching Tape 

Fletching tape from XS Wings.

Key features:

• Fletching tape for securing spin vanes to the shaft.
• Pre-cut for easy use.
• Range of sizes to suit a selection of vane lengths.
• Secure adhesion.
• Package contains 10 sheets - + 1 free sheet!

Technical specifications:

Archery Tech Team